OEM/ODM Factory Continuous Wire Extrusion Machine - Copper Horizontal Enameling Machine – LINT TOP
Product Details
OEM/ODM Factory Continuous Wire Extrusion Machine - Copper Horizontal Enameling Machine – LINT TOP Detail:
1. Introduction
This machine is used to produce enameling wires below 0.8mm, commonly in fan motor wires, motor wires and transformer wires. It can produce 32 wires at the same time. It is even suitable for new factories and new operators for its simple operation.
2. Features
1. With special design, our oven takes full advantage of heat discharged. So our oven almost doesn’t consume the electricity.
2. PLC control for the 4 main control point of the oven to ensure the stability and not be affected by wire break.
3. Exhausted air is fully burned and clean to the air. So no energy loss from exhausting.
4. The structure and material using make sure burning fully under 700℃ for a long time.
3. Technical Parameters
|
Model |
LT-1T/2800-24/10-S |
LT-2T/3000-28/8-S |
LT-4T/4000-32/8-S |
LT-5T/4800-18/10-D(LD2) |
LT-6T/5200-18/10-D(LD2) |
|
Wire Range(mm) |
Φ0.04-0.07 |
Φ0.06-0.10 |
Φ0.10-0.30 |
Φ0.25-0.55 |
Φ0.40-0.80 |
|
DV Value |
24PU |
22/PU |
25/PE |
25/PE |
25/PE |
|
No. of Lines |
24 |
28 |
32/28/24 |
20 |
18 |
|
Max. Passes(Dual Coating) |
10 |
8 |
8 |
9 |
10 |
|
Wire Pitch(mm) |
5 |
5 |
6.5 |
7 |
8 |
|
Φ200-Φ250 |
Φ200-Φ300 |
Φ300-Φ400 |
Φ400-Φ630 |
Φ400-Φ630 |
|
|
Applicator Method |
Felt/Dies |
Felt |
Felt/Dies |
Felt/Dies |
Felt/Dies |
|
PT2-PT4 |
PT2-PT10 |
PT4-PT25 |
D(PT10-PT45)/LD2(PT25-PT270) |
D(PT10-PT45)/LD2(PT25-PT270) |
|
|
Ann. Oven Length(mm) |
3000 |
3500 |
6000 |
9000 |
9000 |
|
Max. Temp of Annealer(℃) |
450 |
450 |
500 |
500 |
550 |
|
Baking Oven Length(mm) |
2800 |
3000 |
4000 |
4800 |
5200 |
|
Catalyst |
Ceramic |
Ceramic |
Ceramic |
Ceramic |
Ceramic |
|
Install Power(Kw) |
110 |
115 |
125 |
145 |
155 |
|
Energy Consumption(KwH/24Hrs) |
600-650 |
650-700 |
300-400 |
350-450 |
450-550 |
|
Out-put(Kgs/24Hrs) |
290(Φ0.05mm) |
540(Φ0.08mm) |
1600(Φ0.20mm) |
2000(Φ0.40mm) |
2370(Φ0.60mm) |
|
Operating Voltage |
380V-50Hz |
380V-50Hz |
380V-50Hz |
380V-50Hz |
380V-50Hz |
|
Consumption/kg |
2.06KwH/Kg |
0.88KwH/Kg |
0.25KwH/Kg |
0.22KwH/Kg |
0.222KwH/Kg |
|
Environment Data VOC(mg/m³) |
≤20 |
≤20 |
≤20 |
≤20 |
≤20 |
Product detail pictures:
Related Product Guide:
With reliable good quality system, great standing and perfect consumer support, the series of products and solutions produced by our organization are exported to quite a few countries and regions for OEM/ODM Factory Continuous Wire Extrusion Machine - Copper Horizontal Enameling Machine – LINT TOP , The product will supply to all over the world, such as: kazakhstan, Plymouth, Moscow, We have been seeking the chances to meet all the friends from both at home and abroad for the win-win cooperation. We sincerely hope to have long-term cooperation with all of you on the bases of mutual benefit and common development.
FAQ
Q: Can I visit your factory?
A: All the customers from both home and abroad are warmly welcomed to visit our company and factory.
Q: Do you supply the installation and commissioning?
A: Yes, we do as followings:
-As soon as customer informed us the machines are put in the right place, we will send both mechanical and electrical engineer for machine start up.
-No-load testing: After machine installed completely, we make no-load testing first.
-With-load testing: Usually we will can produce 3 different wires to make load testing.
-Acceptance report: After the buyer confirms that machine can reach all specification under contract, the acceptance report will be signed for our record that machine will be in guarantee period.
Q: What information should I offer to get a detailed quotation from you?
A: For single machine: Usually we need to know inlet wire size, outlet wire size to be produced, productivity, pay off and take up size to choose the right machine.
For new cable plant or new cable production line, we need to know the datasheet of cables to be produced, the productivity, the standards to be followed, etc to design all machines needed.
Q: Can you supply the auxiliary equipment along with the machines?
A: Yes, definitely.
We has supplied heat exchanger, copper/aluminum powder filter machine, cooling tower, chiller, air compressor, drawing dies, pointing machine, cold welders, bobbins etc. with our machines.
Q: Could you do the design for the whole plant?
A: Yes, this is our advantage.
With the data sheet of cable to be produced, the standard your cables should follows, the productivity you expected. Our engineer on production technology and machinery will make design of production machines, test equipment, accessories like bobbins, dies, rewinding lines and materials needed.
Q: How can I know the status of my order?
A: We have our OA system on tracking the production.
For any of your request we can send photos and videos of your order, also we can use FACETIME to let you know the production.
Q: How do you work on the inspection before delivery?
A: We will make dynamic balance testing, levelness testing, noise testing, etc. during production.
After production finished, usually we make no-load running of each machine before delivery. Customers are welcomed to attend the inspection.
Q: What exhibitions will you attend, can we meet in the fair?
A: Dusseldorf International Wire and Cable Fair;
Wire South America Fair;
International Wire and Cable Fair in Shanghai;
International Istanbul Wire Fair, etc.
wire Southeast Asia Fair, etc.
