Low MOQ for Copper Multiwire Drawing Machine - Copper Horizontal Enameling Machine – LINT TOP

Product Details

FAQ

Product Details

Our eternal pursuits are the attitude of "regard the market, regard the custom, regard the science" as well as the theory of "quality the basic, have confidence in the very first and management the advanced" for Copper Wire Drawing Machine, Fiber Optic Cable Production, Aluminium Wire Drawing, We sincerely welcome overseas consumers to consult for your long-term cooperation as well as the mutual advancement.We strongly think that we will do superior and far better.

Low MOQ for Copper Multiwire Drawing Machine - Copper Horizontal Enameling Machine – LINT TOP Detail:

1. Introduction

This machine is used to produce enameling wires below 0.8mm, commonly in fan motor wires, motor wires and transformer wires. It can produce 32 wires at the same time. It is even suitable for new factories and new operators for its simple operation.

2. Features

1. With special design, our oven takes full advantage of heat discharged. So our oven almost doesn’t consume the electricity.
2. PLC control for the 4 main control point of the oven to ensure the stability and not be affected by wire break.
3. Exhausted air is fully burned and clean to the air. So no energy loss from exhausting.
4. The structure and material using make sure burning fully under 700℃ for a long time.

3. Technical Parameters

Model	LT-1T/2800-24/10-S	LT-2T/3000-28/8-S	LT-4T/4000-32/8-S	LT-5T/4800-18/10-D(LD2)	LT-6T/5200-18/10-D(LD2)
Wire Range(mm)	Φ0.04-0.07	Φ0.06-0.10	Φ0.10-0.30	Φ0.25-0.55	Φ0.40-0.80
DV Value	24PU	22/PU	25/PE	25/PE	25/PE
No. of Lines	24	28	32/28/24	20	18
Max. Passes(Dual Coating)	10	8	8	9	10
Wire Pitch(mm)	5	5	6.5	7	8
Pay-off Spool Size	Φ200-Φ250	Φ200-Φ300	Φ300-Φ400	Φ400-Φ630	Φ400-Φ630
Applicator Method	Felt/Dies	Felt	Felt/Dies	Felt/Dies	Felt/Dies
Take-up Spool Size	PT2-PT4	PT2-PT10	PT4-PT25	D(PT10-PT45)/LD2(PT25-PT270)	D(PT10-PT45)/LD2(PT25-PT270)
Ann. Oven Length(mm)	3000	3500	6000	9000	9000
Max. Temp of Annealer(℃)	450	450	500	500	550
Baking Oven Length(mm)	2800	3000	4000	4800	5200
Catalyst	Ceramic	Ceramic	Ceramic	Ceramic	Ceramic
Install Power(Kw)	110	115	125	145	155
Energy Consumption(KwH/24Hrs)	600-650	650-700	300-400	350-450	450-550
Out-put(Kgs/24Hrs)	290(Φ0.05mm)	540(Φ0.08mm)	1600(Φ0.20mm)	2000(Φ0.40mm)	2370(Φ0.60mm)
Operating Voltage	380V-50Hz	380V-50Hz	380V-50Hz	380V-50Hz	380V-50Hz
Consumption/kg	2.06KwH/Kg	0.88KwH/Kg	0.25KwH/Kg	0.22KwH/Kg	0.222KwH/Kg
Environment Data VOC(mg/m³)	≤20	≤20	≤20	≤20	≤20

Product detail pictures:

FAQ

Q: Can I visit your factory?

A: All the customers from both home and abroad are warmly welcomed to visit our company and factory.

Q: Do you supply the installation and commissioning?
A: Yes, we do as followings:
-As soon as customer informed us the machines are put in the right place, we will send both mechanical and electrical engineer for machine start up.
-No-load testing: After machine installed completely, we make no-load testing first.
-With-load testing: Usually we will can produce 3 different wires to make load testing.

-Acceptance report: After the buyer confirms that machine can reach all specification under contract, the acceptance report will be signed for our record that machine will be in guarantee period.

Q: What information should I offer to get a detailed quotation from you?
A: For single machine: Usually we need to know inlet wire size, outlet wire size to be produced, productivity, pay off and take up size to choose the right machine.
For new cable plant or new cable production line, we need to know the datasheet of cables to be produced, the productivity, the standards to be followed, etc to design all machines needed.

Q: Can you supply the auxiliary equipment along with the machines?
A: Yes, definitely.
We has supplied heat exchanger, copper/aluminum powder filter machine, cooling tower, chiller, air compressor, drawing dies, pointing machine, cold welders, bobbins etc. with our machines.

Q: Could you do the design for the whole plant?
A: Yes, this is our advantage.
With the data sheet of cable to be produced, the standard your cables should follows, the productivity you expected. Our engineer on production technology and machinery will make design of production machines, test equipment, accessories like bobbins, dies, rewinding lines and materials needed.

Q: How can I know the status of my order?
A: We have our OA system on tracking the production.
For any of your request we can send photos and videos of your order, also we can use FACETIME to let you know the production.

Q: How do you work on the inspection before delivery?
A: We will make dynamic balance testing, levelness testing, noise testing, etc. during production.
After production finished, usually we make no-load running of each machine before delivery. Customers are welcomed to attend the inspection.

Q: What exhibitions will you attend, can we meet in the fair?
A: Dusseldorf International Wire and Cable Fair;
Wire South America Fair;
International Wire and Cable Fair in Shanghai;
International Istanbul Wire Fair, etc.
wire Southeast Asia Fair, etc.